Sysadmin Todo List

This is an unordered set of tasks. Detailed information on any of the tasks typically goes in related topics' pages, although usually not until the task has been filed under Completed.

Daily Check off list

Each day when you come in check the following:

Einstein (script):
1. Up and running?
2. Disks are at less than 90% full?
3. Mail system OK? (spamassasin, amavisd, ...)
Temperature OK? No water blown into room?
Systems up: Taro, Pepper, Pumpkin/Corn ?
Backups:
1. Did backup succeed?
2. Does Lentil need a new disk?

Important

Weather

Judging by the look of the post-it-notes on the wall, the fan was blowing some sort of weather in. We need to figure out a way to prevent the outside from coming inside. We're lucky roentgen seems okay. What about using screen material in front of the fan, oriented in such a way that any water will run down the screen and collect at the water sensor?

Now that we're experiencing a mini heat wave, the fan and line air conditioner aren't quite enough to keep the temperature below 70°F. The standard operating procedure has been to leave the door open during the day.

Pumpkin/Corn

Our new system needs to be setup and integrated/tied in. Read more: Pumpkin

Einstein Upgrade

Einstein upgrade project and status page: Einstein Status Note: Einstein (current one) has a problem with / getting full occasionally. See Einstein#Special_Considerations_for_Einstein

Environmental Monitor

We have an environmental monitor running at http://10.0.0.98 This is capable of sending email and turning the fan on and off (needs to be set up more intelligently). It responds to SNMP so we can integrate it with Cacti (needs to be done). Cacti doesn't support traps, as it's a polling tool. A possible workaround is to have another daemon run that captures traps and writes them somewhere cacti can pick them up, such as syslog. Or, maybe we can just use splunk instead.

Miscellaneous

Clean out some users who have left a while ago. (Maurik should do this.)
Monitoring: I would like to see the new temp-monitor integrated with Cacti, and fix some of the cacti capabilities, i.e. tie it in with the sensors output from pepper and taro (and tomato/einstein). Setup sensors on the corn/pumpkin. Have an intelligent way in which we are warned when conditions are too hot, a drive has failed, a system is down.
Check into smartd monitoring (and processing its output) on Pepper, Taro, Corn/Pumpkin, Einstein, Tomato.
Decommission Okra. - This system is way too outdated to bother with it. Move Cacti to another system. Perhaps a VM, once we get that figured out?
Decide whether we want to decommission Jalapeno. It is currently not a stable system, and perhaps not worth the effort trying to make it stable. It's only service is Splunk, which can be moved to another system (which?). We could "rebuild" the HW if there is need.
Maybe this should be fixed when we do lentil: When I was checking root's email, I waded through the logwatch reports and found that gourd's been giving smartd errors, namely

Offline uncorrectable sectors detected:
       /dev/sda [3ware_disk_00] - 48 Time(s)
       1 offline uncorrectable sectors detected

Okra also has an offline uncorrectable sector!

Continue purgin NIS from ancient workstations, and replacing with files. The following remain:
- pauli nodes -- Low priority!
Learn how to use cacti on okra. Seems like a nice tool, mostly set up for us already. Find out why lentil isn't being read by cacti. Install the net-snmp package, copy the /etc/snmpd/snmpd.conf from a working machine to the new one, start the snmpd service. Still not working though. Lentil won't start iptables-netgroups ("Net::SSLeay object version 1.30 does not match bootstrap parameter 1.25 at /usr/lib/perl5/5.8.8/i386-linux-thread-multi/DynaLoader.pm line 253, line 225. Compilation failed in require at /usr/lib/perl5/vendor_perl/5.8.8/IO/Socket/SSL.pm line 17, line 225. BEGIN failed--compilation aborted at /usr/lib/perl5/vendor_perl/5.8.8/IO/Socket/SSL.pm line 17, line 225. Compilation failed in require at /usr/lib/perl5/vendor_perl/5.8.8/Net/LDAP.pm line 156, line 225."), maybe that's why. Lentil and pumpkin have the same Perl packages installed, yet pumpkin doesn't fail at starting the script.
Heiseinberg dropped pauli off today. Says it's his power supply. Very low priority.

Ongoing

Documentation

Maintain the Documentation of all systems!
- Main function
- Hardware
- OS
- Network
Continue homogenizing the configurations of the machines.
Improve documentation of mail software, specifically SpamAssassin, Cyrus, etc.

Maintenance

Check e-mails to root every morning
Resize/clean up partitions as necessary. Seems to be a running trend that a computer gets 0 free space and problems crop up. Symanzik, bohr seem imminent. Yup, bohr died. Expanded his root by 2.5 gigs. Still serious monitor problems though, temporarily bypassed with vesa... Bohr's problem seems tied to the nvidia drivers, let's wait until the next release and see how those work out.
Check up on security [1]
Clean up Room 202.
- Ask UNH if they have are willing/able to recycle/reuse the three CRTs that we have sitting around.

On-the-Side

See if we can get the busted printer in 322 to work down here.
Learn how to use ssh-agent for task automation.
Backup stuff: We need exclude filters on the backups. We need to plan and execute extensive tests before modifying the production backup program. Also, see if we can implement some sort of NFS user access. I've set up both filters and read-only snapshot access to backups at home. Uses what essentially amounts to a bash script version of the fancy perl thing we use now, only far less sophisticated. However, the filtering and user access uses a standard rsync exclude file (syntax in man page) and the user access is fairly obvious NFS read-only hosting. I am wondering if this is needed. The current scheme (ie the perl script) uses excludes by having a .rsync-filter is each of the directories where you want excluded contents. This has worked well. See ~maurik/tmp/.rsync-filter . The current script takes care of some important issues, like incomplete backups. Ah. So we need to get users to somehow keep that .rsync-filter file fairly updated. And to get them to use data to hold things, not home. Also, I wasn't suggesting we get rid of the perl script, I was saying that I've become familiar with a number of the things it does. [2] Put this on the backburner for now, since the current rate of backup disk consumption will give about 10 months before the next empty disk is needed.

Waiting

jalapeno hangups: Look at sensors on jalapeno, so that cacti can monitor the temp. The crashing probably isn't the splunk beta (no longer beta!), since it runs entirely in userspace. lm_sensors fails to detect anything readable. Is there a way around this? Jalapeno's been on for two weeks with no problems, let's keep our fingers crossed…
That guy's computer has a BIOS checksum error. Flashing the BIOS to the newest version succeeds, but doesn't fix the problem. No obvious mobo damage either. What happen? Who was that guy, anyhow? (Silviu Covrig, probably) The machine is gluon, according to him. Waiting on ASUS tech support for warranty info Aaron said it might be power-supply-related. Nope. Definitely not. Used a known good PSU and still got error, reflashed bios with it and still got error. Got RMA, sending out on wed. Waiting on ASUS to send us a working one! Called ASUS on 8/6, they said it's getting repaired right now. Wohoo! Got a notification that it shipped! ...they didn't fix it... Still has the EXACT same error it had when we shipped it to them. What should we do about this? I'm going to call them up and have a talk, considering looking at the details on their shipment reveals that they sent us a different motherboard, different serial number and everything but with the same problem.
Printer queue for Copier: Konica Minolta Bizhub 750. IP=pita.unh.edu Seems like we need info from the Konica guy to get it set up on Red Hat. The installation documentation for the driver doesn't mention things like the passcode, because those are machine-specific. Katie says that if he doesn't come on Monday, she'll make an inquiry. Mac OS X now working, IT guy should be here week of June 26th Did he ever come? No, he didn't, and did not respond to a voice message left. Will call again.
Pauli crashes nearly every day, not when backups come around. We need to set up detailed system logging to find out why. Pauli2 and 4 don't give out their data via /net to the other paulis. This doesn't seem to be an autofs setting, since I see nothing about it in the working nodes' configs. Similarly, 2,4, and 6 won't access the other paulis via /net. 2,4 were nodes we rebuilt this summer, so it makes sense they don't have the right settings, but 6 is a mystery. Pauli2's hard drive may be dying. Some files in /data are inaccessible, and smartctl shows a large number of errors (98 if I'm reading this right...). Time to get Heisenberg a new hard drive? Or maybe just wean him off of NPG… It may be done for; can't connect to pauli2 and rebooting didn't seem to work. Need to set up the monitor/keyboard for it & check things out. The pauli nodes are all off for now. They've been deemed to produce more heat than they're worth. We'll leave them off until Heisenberg complains. Heisenberg's complaining now. Fixed his pauli machine by walking in the room (still don't know what he was talking about) and dirac had LDAP shut off. He wants the paulis up whenever possible, which I explained could be awhile because of the heat issues.
Sent an email to UNH Property Control asking what the procedure is to get rid of untagged equipment, namely, the two old monitors in the corner. Apparently they want us to fill out lots of information on the scrapping form like if it was paid for with government money, etc, as well as give them serial numbers, model numbers, and everything we can get ahold of. Then, we get to hang onto them until the hazardous equipment people come in and take it out, at their leisure. Waiting to figure out what we want to do with them.

Completed

Corn Virtualization issues resolved!
- Subscription is now a "virtual subscription"
- Corn now has 2 ethernets, one to farm one to unh, and resolves "einstein" to 10.0.0.248
- All disks are now mountable.
Properly configure iptables on corn.
- Copy /usr/local/bin/netgroup2iptables.pl from taro (requires perl-LDAP RPM). Copy /etc/init.d/iptables-netgroups, make sure it starts for run level 3 and 5.
- On pumpkin, make sure the guest OSes don't get blocked by pumpkin's iptables.
Properly configure access restrictions to "farm" and root login only from einstein.
Lentil Backup issue resolved!
- The cron job is mailing this message: "archive disk '/mnt/npg-daily-current' does not exist or is not a symlink at /usr/local/bin/rsync_backup.pl line 44, line 1." That link exists, though. I can see it and its contents as a regular user; why can't the script when run by cron? The e-mail may have been outdated … today's was a successful listing. It is fixed, hooray. We just need to fix the ssh keys for tomato and corn so they can be connected to. Lentil now knows all the ssh keys of everyone, made as human-readable as possible.
- First of all Do NOT use disks smaller than 350 GB for backup!!, since those will not even fit one copy of what needs to be backed up.
- The link /mnt/npg-daily-current must exist and point to an actual drive.
- Old entry: Lentil's not doing backups. I tried manually runing the script friday afternoon and the email log looks like it was backing up and stopped for no real reason. Checking the space on the drives (since the script seems unable to do so now), I found that npg-daily/28 is basically full, and npg-daily/29 is an untouched 250gb. Maybe an update screwed around with how the script checks free space, preventing it from knowing how to move to the next drive. It's probably not any update - lentil was working fine until "The Friday Taro Event". I manually made the new symbolic link from /mnt/npg-daily-current -> /mnt/npg-daily/29 . Maybe this'll fix it? That seems to be a no. Lots of unable to make hard link errors, invalid cross-device link, and similar errors. It needs to know to copy the data it's backing up to the disk since it's a new disk. I still think it's got something to do with that unable to statfs error.
New pumpkin network problems: It's possible to reach the farm subnet if pumpkin is booted without starting iptables. Double-check the configs. The problem was that iptables was getting its config from both /etc/iptables and /etc/iptables-npg. Since pepper doesn't have /etc/iptables, I just moved it to /etc/iptables.bak and voilà: everything works.
benfranklin is apparently up and running somewhere, because it's reporting drive issues too: Benfranklin is Dan's workstation, it's in the room next to Maurik's office. BenFranklin is a Pentium III "Coppermine" at 800MHz. I have ordered a replacement system already, so we can decommission the old BenFranklin. The new BF has arrived.
Try to pull as much data from Jim William's old drives as possible, if there's even anything on them. They seem dead. Maybe we can swap one board to the other drive and see if it works? What room is he in? His computer is working now (the ethernet devices will have to be changed to a non-farm setup once the machine is back in his office). The computer is delivered, and he says everything's back. Leads me to believe that all his data wasn't on his drives, but on his home directory. Those drives can be junked now.
At some point, cacti stopped being able to monitor einstein. Update-related? There are no errors in cacti.log, but the status page for einstein just says "down". Cacti was set to use the wrong version of rrdtool.
Added Steve and Matt to the environmental mailing list. There seems to be a problem with more than 1 cc recipient, so to get around this the monitor sends to npg-admins@physics.unh.edu. Tested and it works.
Install the right SNMP stuff on tomato so that it can be graphed
Service snmpd won't start on okra ("Starting snmpd: /usr/sbin/snmpd: error while loading shared libraries: libbeecrypt.so.6: cannot enable executable stack as shared object requires: Permission denied", supposedly SELinux-related). It was SELinux. Fixed!
Taro has become unstable again when running multi-processor. Try another Power supply. If that is not it, give up? Put the new one in, passed memtest, and booted smp. Let's see how it handles itself!
Lentil has a dead disk ("hde0", probably IDE) in its RAID1. It needs replaced. Had a spare Seagate sitting around of just the right size.